OPTICAL, PHOTOGRAPHIC, CINEMATOGRAPHIC, MEASURING, CHECKING, PRECISION, MEDICAL OR SURGICAL INSTRUMENTS AND APPARATUS > OPTICAL, PHOTOGRAPHIC, CINEMATOGRAPHIC, MEASURING, CHECKING, PRECISION, MEDICAL OR SURGICAL INSTRUMENTS AND APPARATUS; PARTS AND ACCESSORIES THEREOF > Measuring or checking instruments, appliances and machines, not specified or included elsewhere in this chapter; profile projectors
This chapter does not cover: articles for general technical purposes (e.g. pumps of heading 8413, metal or graphite packings of heading 8484), parts of general use as defined in Note 2 to Section XV (base metal) or similar parts of plastics (Chapter 39), transfer pumps of heading 8413, or weighing machinery of heading 8423. Note 2 (Parts and accessories): Parts and accessories which are goods included in any heading of this chapter or of Chapter 84, 85 or 91 are classified in their respective headings. Other parts and accessories solely or principally used with instruments of this chapter are classified in heading 9033. The chapter covers a very broad range from lenses and prisms (heading 9001) through microscopes, telescopes, lasers, navigational instruments, drawing instruments, measuring instruments, medical instruments, to X-ray apparatus and physical/chemical analysis instruments.
1. This Section does not cover: (a) articles of a kind used in machines, appliances or for other technical uses, of vulcanised rubber other than hard rubber (heading 4016), of leather or of composition leather (heading 4205) or of textile material (heading 5911); (b) supporting belts or other support articles of textile material whose intended effect on the organ to be supported or held derives solely from their elasticity (for example, maternity belts, thoracic support bandages, abdominal support bandages, supports for joints or muscles) (Section XI); (c) refractory goods of heading 6903; ceramics for laboratory, chemical or other technical uses of heading 6909; (d) glass mirrors, not optically worked, of heading 7009, or mirrors of base metal or of precious metal, not being optical elements (heading 8306 or Chapter 71); (e) goods of heading 7007, 7008, 7011, 7014, 7015 or 7017; (f) parts of general use, as defined in Note 2 to Section XV, of base metal (Section XV) or similar goods of plastics (Chapter 39); however, articles specially designed for use exclusively as parts of specific instruments or apparatus are excluded from this category; (g) pumps, compressors and fans (heading 8413, 8414 or 8421); (h) weighing machinery (heading 8423); lifting machinery (headings 8425 to 8428); (ij) paper- or paperboard-cutting machines (heading 8441); fittings for adjusting work or tools on machine tools or water-jet cutting machines, of heading 8466, including fittings with optical devices for reading scales (e.g. 'optical' dividing heads) but not those which are in themselves essentially optical instruments (e.g. alignment telescopes); (k) articles of Chapter 95. 2. Subject to Note 1 above, parts and accessories for machines, apparatus, instruments or articles of this Section are to be classified according to the following rules: (a) parts and accessories which are goods included in any of the headings of this Section or of Section XV, XVI or XVII are in all cases to be classified in their respective headings; (b) other parts and accessories, if suitable for use solely or principally with a particular kind of machine, instrument or apparatus, or with a number of machines, instruments or apparatus of the same heading, are to be classified with the machines, instruments or apparatus of that kind; (c) all other parts and accessories are to be classified in heading 9033.
Source: European Commission - CN Explanatory Notes (CNEN) and HS legal notes.
2015/805
An electronic industrial gyroscope (35 g, 24 × 24 × 28 mm) incorporating up to three angular velocity sensors and a thermal probe to measure and compensate angular velocities from 50 to 1200°/s. The device generates an electrical signal proportional to rotation, transmitted via cable to machines or installations (wind turbines, motors, industrial equipment) for adjustment or control of their positioning. This component falls under electronic measurement or detection instruments for industrial use, subject to CE obligations (safety, EMC, RoHS) and REACH depending on the composition of the materials and electronic components integrated.
1212/2013
This is an electronic device intended for measuring and monitoring heart rate, consisting of a heart rate sensor with an integrated wireless transmitter embedded in a chest strap, and a receiver device with optoelectronic display (multifunction wristwatch) that can be worn on the wrist or attached to a bicycle handlebar. The set allows wireless transmission, calculation, and display of heart rate in real-time, along with additional functions such as stopwatch and clock; it is primarily used in sports activities or health monitoring. No specific regulatory requirements are mentioned, but compliance obligations (e.g., electromagnetic compatibility, CE marking) may apply.
1212/2013
This is an electronic device intended for measuring and monitoring heart rate, consisting of a heart rate sensor with an integrated wireless transmitter embedded in a chest strap, and a receiver device with optoelectronic display (multifunction wristwatch) that can be worn on the wrist or attached to a bicycle handlebar. The set allows wireless transmission, calculation, and display of heart rate in real-time, along with additional functions such as stopwatch and clock; it is primarily used in sports activities or health monitoring. No specific regulatory requirements are mentioned, but compliance obligations (e.g., electromagnetic compatibility, CE marking) may apply.