Customs Search

ROTARY STEERABLE WELLBORE DRILL. THE GEO-PILOT SYSTEM IS DESIGNED TO DRILL A HIGHER QUALITY WELLBORE AND TO MINIMISE THE HOLE SPIRALLING , ELIMINATING TRAPS ALONG THE BOTTOM OF THE HOLE WHERE CUTTINGS ACCUMULATE.IT CONSISTS OF A SHAFT SUPPORTED BY TWO BEARINGS INSIDE AN OUTER HOUSING ,MEASURING APPROXIMATELY 18 FEET IN LENGTH. ROTARY SEALS AT EITHER END COMPLETELY ENCLOSE THE TOOL. THE TOP OF THE TOOL IS CONNECTED IN THE CONVENTIONAL WAY , VIA DRILL PIPE, TO THE TOP DRIVE AND THUS ROTARY POWER IS TRANSMITTED TO THE DRILL BIT.IT INCORPORATES EXTENSIVE SELF DIAGNOSTIC CAPABILITY,IN ADDITION TO THE EXPECTED GEOMETRICAL VALUES , MECHANICAL AND ELECTRONIC MEASUREMENTS ARE TAKEN, WHICH ALLOW READY DIAGNOSIS OF WHETHER A PERCIEVED PROBLEM IS CAUSED BY THE DRILLING OPERATION OR BY THE TOOL FUNCTION.

THIS PRODUCT IS A 48.50 INCH MOULD TUBE THAT IS USED TO MAKE HIGH ALLOY BARS. THE MOULD IS MADE FROM A LOW/MILD CARBON STEEL SEAMLESS TUBE OF CIRCULAR CROSS SECTION, DRAWN TO TOLERANCE. THE MOULD IS PLACED IN A SET, WHICH SEALS THE BOTTOM, AND THE RECESS HOLDS THE POURING HEAD. THE SET IS THEN PLACED IN A FURNACE WHERE THE MOLTEN SUPER ALLOY IS ALLOWED TO COOL, AND IS THEN EXTRUDED FROM THE MOULD USING A HYDRAULIC RAM. THIS MOULD HAS TWO ANGLED CHAMFERS TO HOUSE THE POURING HEAD, THAT ARE ANGLED AT 45 DEGREES, WITH AN EDGE OF 2MM. THE DIMENSIONS OF THIS STEEL MOULD ARE LENGTH 1232.00 MM, WITH AN OUTSIDE DIAMETER OF 168.30 MM, AN INTERNAL DIAMETER OF 127.00 MM, WITH A WEIGHT OF 92.63KG. MADE OF EN10305-1 E235+C.

THIS PRODUCT IS A 47.72 INCH MOULD TUBE THAT IS USED TO MAKE HIGH ALLOY BARS. THE MOULD IS MADE FROM A LOW/MILD CARBON STEEL SEAMLESS TUBE OF CIRCULAR CROSS SECTION, DRAWN TO TOLERANCE. THE MOULD IS PLACED IN A SET, WHICH SEALS THE BOTTOM, AND THE RECESS HOLDS THE POURING HEAD. THE SET IS THEN PLACED IN A FURNACE WHERE THE MOLTEN SUPER ALLOY IS ALLOWED TO COOL, AND IS THEN EXTRUDED FROM THE MOULD USING A HYDRAULIC RAM. THIS MOULD HAS TWO ANGLED CHAMFERS TO HOUSE THE POURING HEAD, THAT ARE ANGLED AT 45 DEGREES, WITH AN EDGE OF 2MM. THE DIMENSIONS OF THIS STEEL MOULD ARE LENGTH 1212 MM, WITH AN OUTSIDE DIAMETER OF 194.00 MM, AN INTERNAL DIAMETER OF 152.40.00 MM, AND A WEIGHT OF 92.63 KG. MADE OF EN10305-1 E235+C.

THIS PRODUCT IS A 47.09 INCH MOULD TUBE THAT IS USED TO MAKE HIGH ALLOY BARS. THE MOULD IS MADE FROM A LOW/MILD CARBON STEEL SEAMLESS TUBE OF CIRCULAR CROSS SECTION, DRAWN TO TOLERANCE. THE MOULD IS PLACED IN A SET, WHICH SEALS THE BOTTOM, AND THE RECESS HOLDS THE POURING HEAD. THE SET IS THEN PLACED IN A FURNACE WHERE THE MOLTEN SUPER ALLOY IS ALLOWED TO COOL, AND IS THEN EXTRUDED FROM THE MOULD USING A HYDRAULIC RAM. THIS MOULD HAS TWO ANGLED CHAMFERS TO HOUSE THE POURING HEAD, THAT ARE ANGLED AT 45 DEGREES, WITH AN EDGE OF 2MM. THE DIMENSIONS OF THIS STEEL MOULD ARE LENGTH 1196 MM, WITH AN OUTSIDE DIAMETER OF 244.50 MM, AN INTERNAL DIAMETER OF 177.80 MM, AND A WEIGHT OF 207.70 KG. MADE OF EN10305-1 E235+C

THIS PRODUCT IS A 51.02 INCH MOULD TUBE THAT IS USED TO MAKE HIGH ALLOY BARS. THE MOULD IS MADE FROM A LOW/MILD CARBON STEEL SEAMLESS TUBE OF CIRCULAR CROSS SECTION, DRAWN TO TOLERANCE. THE MOULD IS PLACED IN A SET, WHICH SEALS THE BOTTOM, AND THE RECESS HOLDS THE POURING HEAD. THE SET IS THEN PLACED IN A FURNACE WHERE THE MOLTEN SUPER ALLOY IS ALLOWED TO COOL, AND IS THEN EXTRUDED FROM THE MOULD USING A HYDRAULIC RAM. THIS MOULD HAS TWO ANGLED CHAMFERS TO HOUSE THE POURING HEAD, THAT ARE ANGLED AT 45 DEGREES, WITH AN EDGE OF 2MM. THE DIMENSIONS OF THIS STEEL MOULD ARE LENGTH 1296 MM, WITH AN OUTSIDE DIAMETER OF 114.30, AN INTERNAL DIAMETER OF 88.90, AND A WEIGHT OF 41.24KG. MADE OF EN10305-1 E235+C.