Customs Search

CT3 Texture Analyzer compression & tension testing for rapid QC analysis see technical literature THE MOST POWERFUL, LOW COST, STAND ALONE TEXTURE ANALYZER EVER PRODUCED. WITH SIX TEST MODES (PLUS CALIBRATION CHECK) AND A WIDE CHOICE OF ACCESSORIES, NO OTHER TEXTURE ANALYZER HAS EVER DONE SO MUCH WITHOUT REQUIRING A COMPUTER AND SOFTWARE. STANDARD TEST MODES NORMAL TEST: A SINGLE COMPRESSION CYCLE HOLD TIME TEST: COMPRESS AND HOLD CYCLE COUNT TEST: COMPRESS MULTIPLY TIMES BLOOM TEST: GELATIN BLOOM STRENGTH TEST TPA TEST: TEXTURE PROFILE ANALYSIS TENSION TEST: TENSILE TESTING SURIMI TEST: GEL STRENGTH STATIC LOAD TEST: CALIBRATION CHECK TEXTURE LOADER SOFTWARE ALLOWS UP TO TEN CUSTOMS TESTS AND ABILITY TO LOCK PARAMETERS COMPRESSION DISTANCE UP TO 10CM, CAN ACCOMMODATESAMPLE UP TO 22.5CM ALMOST 9 INCHES TALL. PROBE SHAFT IS 8CM FROM BACK WALL. CHOICE OF LOAD CELLS 7 MEASUREMENT RANGES UP TO 50KG CHOICE OF BASE TABLES ALLOWS FOR LARGER SAMPLES AND MORE ACCESSORY CHOICES. INCLUDES INSTRUMENT WITH A CHOICE OF LOAD CELL, TEXTURE LOADER SOFTWARE AND USB CABLE.

AN ELECTRONIC DEVICE USED FOR TESTING CONTAINER IMPACT RESISTANCE. THE SAMPLE IS PLACED IN THE PENDULUM MECHANISM AND SUBJECTED TO REPEAT IMPACTS WITH THE PENDULUM UNTIL IT DESTRUCTS. THIS TEST DETERMINES THE RESISTANCE OF GLASS CONTAINERS (BOTTLES AND JARS) TO AN IMPACT LOAD. THE HEIGHT/ANGLE OF THE PENDULUM INCREASES AFTER EACH IMPACT.

A SEMI AUTOMATIC STRESS CRACK TESTER IS A DEVICE TO TEST A PLASTIC BOTTLES ABILITY TO WITHSTAND INTERNAL PRESSURE. TYPICALLY A BOTTLE IS FILLED WITH WATER UP TO THE FILL POINT, AN ADAPTOR IS PLACED INSTEAD OF THE USUAL CAP, IT IS PLACED IN THE MACHINE AND 5 BAR AIR PRESSURE APPLIED, THE BASE OF THE BOTTLE SITS IN A CAUSTIC SOLUTION TO ACCELERATE DEGREDATION OF THE BOTTLE. TIME FOR BOTTLE TO BURST IS MONITORED AND RECORDED.

A FOUR CHANNEL SHOCK AND IMPACT STIMULATION SYSTEM, CONSIST OF FOUR HIGH VELOCITY HYDRAULICALLY DRIVEN ACTUATORS AND ASSOCIATED HARDWARE. THE ACTUATORS ARE ESSENTIALLY PISTONS DRIVEN BY HIGH PRESSURE OIL, VIA ACCUMULATORS MOUNTED ON THE BODY OF THE PISTONS. THE COMPLETE SYSTEM CONSISTS OF FOUR ACTUATORS, TWO SMALL AND TWO LARGE. ASSOCIATED WITH THE ACTUATORS ARE; A DATA ACQUISITION SYSTEM FOR MEASURING ACCLERATION AND POSITION OF THE ACTUATORS TO ENABLE THEM TO BE CONTROLLED, USING A DEDICATED CONTROL SYSTEM, A HYDRAULIC POWER SUPPLY, FOR CHARGING THE ACCUMULATORS WHICH DRIVE THE ACTUATOR WITH OIL AND GUIDE RAILS FOR SUPPORTING MASSES AND 'PROGRAMMERS' WHICH ARE FIXED TO THE ENDS OF THE ACTUATOR PISTONS. THE PROGRAMMERS ARE SIMPLY ELASTOMERIC FACINGS WHICH FIT ON THE FACE OF EACH MASS ATTACHED TO EACH ACTUATOR. THE ACTUATORS ARE USED TO STIMULATE THE EFFECTS OF SHOCK OR IMPACT ON STRUCTURAL TEST SPECIMENS (SUCH AS WALLS, COLUMNS, CLADDING PANELS, BEAMS). THE ACTUATORS ARE USED SINGLY OR IN COMBINATION TO LOAD TEST SPECIMENS WITHIN A CONTROLLED LABORATORY ENVIRONMENT. THE MASSES ON THE ENDS OF THE ACTUATORS ARE ALLOWED TO COLLIDE WITH THE TEST SPECIMEN TO PROVIDE A HIGH ENERGY IMPULSIVE LOADING SO THAT STRUCTURAL RESPONSE CAN BE MEASURED AND OBSERVED. THE OUTPUT OF THE TESTS IS TO ASSIST WITH ACADEMIC RESEARCH AT THE UNIVERSITY OF BATH. THE VALUE OF THE COMPLETE SYSTEM IS $2,100,000.

ELECTRICAL TEST APPLIANCE FOR TESTING THE PHYSICAL AND MECHANICAL PROPERTIES OF MATERIALS, SUCH AS METAL, PLASTIC, GLASS, PAPER AND PAINT. DEVICE WORKS BY SPRAYING THE MATERIAL WITH A FIVE PERCENT SODIUM CHLORIDE SOLUTION AT A CONTROLLED TEMPERATURE OF 35 DECREES C, FOR AN UNSPECIFIED DURATION. THE TEST OPERATES TO VARIOUS TEST METHODS AND THESE TEST CABINETS ARE USED IN THE LABORATORY OF THE BUSINESS CUSTOMERS.